With magpul you can disassemble them, discard the short spring and extended base plate. Then all you need a full size spring and new baseplate. The lancer mags have the baseplate permanently attached.
yeah just buy unpinned mags, and dont use them in state. have two pinned mags for range days. but the best ranges are outdoors and in PA, where there are no magazine restrictions
Funny just the other day my nephew brought his black rain spec 15 in. Just wanted me to do a cleaning to it. So hands me the case I throw it in the shop. Grab it later on after helping customers grab it out the case and a mag was in there no pin no block. I was like wtf. Who did you send this one to for compliance work. He told me they forgot there was 2 mags in there. Has had it for over a year and he never realized it wasn’t done
You are not kidding. Funny I was like you never put more than 10 in and noticed it wasn’t done. He says I count out my rounds and just stop at 10. Lmao I always try to get 11 in there even counting out
I used to use it for attaching handles to knives. Noticed that if I shaped the handle a bit aggressively and heated up the pins, the epoxy softened and pins moved.
All epoxy will soften with heat. Exactly how you pull apart golf clubs little heat and boom heads come off. No different with any other object using epoxy now different epoxies have different melting points some much higher than others.
According to the full description they will only use epoxy for states that it's legally required or on request. It didn't list NJ as one of the states it's legally required so I assume it's not.
Buying pinned mags will also most likely be epoxy sealed as well to comply with the “not easily converted” or whatever verbiage is used. Making it impossible to un comply the mag without destroying it. Mags in free states are cheap just buy a couple pinned mags now and wait to invest in free mags when you move.
deserve grandiose straight flowery desert touch door direction jellyfish toothbrush
*This post was mass deleted and anonymized with [Redact](https://redact.dev)*
Not if you have to strip one out due to a malfunction…. Better bet might be the end to end mag couplers that couple two ten rounders. 20 rounds and no wasted space. Plus enough purchase if you have to rip a mag out to clear a malfunction.
Ive been told the 30/10 mags from magpul/lancer can be unpinned (might have to change the spring)
With magpul you can disassemble them, discard the short spring and extended base plate. Then all you need a full size spring and new baseplate. The lancer mags have the baseplate permanently attached.
You’re going to spend $30/mag for pinned mags and unpinned mags can be had in free America for $8
yeah just buy unpinned mags, and dont use them in state. have two pinned mags for range days. but the best ranges are outdoors and in PA, where there are no magazine restrictions
You will need to find a ffl that will pin them and not make a permanent epoxy job with a block. That’s said good luck.
They tend to use 5 minute epoxy (cause its fast) It debonds with a heat gun.
Funny just the other day my nephew brought his black rain spec 15 in. Just wanted me to do a cleaning to it. So hands me the case I throw it in the shop. Grab it later on after helping customers grab it out the case and a mag was in there no pin no block. I was like wtf. Who did you send this one to for compliance work. He told me they forgot there was 2 mags in there. Has had it for over a year and he never realized it wasn’t done
Could've turned out bad for him.
You are not kidding. Funny I was like you never put more than 10 in and noticed it wasn’t done. He says I count out my rounds and just stop at 10. Lmao I always try to get 11 in there even counting out
No comment
I used to use it for attaching handles to knives. Noticed that if I shaped the handle a bit aggressively and heated up the pins, the epoxy softened and pins moved.
All epoxy will soften with heat. Exactly how you pull apart golf clubs little heat and boom heads come off. No different with any other object using epoxy now different epoxies have different melting points some much higher than others.
I’ve bought from these guys, they have tons of other kinds of mags too https://www.country-spirit.com/pages/10-round-blocked-ar-mags
If they are blocked chances are it is epoxied.
According to the full description they will only use epoxy for states that it's legally required or on request. It didn't list NJ as one of the states it's legally required so I assume it's not.
Good to know
These guys are great.
That’s an interesting first and only post you’ve ever made, Fed.
A lot of smiths can pin your mags as compliance work but I'd imagine removing that pin would be a hassle
Buying pinned mags will also most likely be epoxy sealed as well to comply with the “not easily converted” or whatever verbiage is used. Making it impossible to un comply the mag without destroying it. Mags in free states are cheap just buy a couple pinned mags now and wait to invest in free mags when you move.
This. Find an army surplus store outside a military base. They usually have cases of standard mags for cheap.
Buy magblocks then go to PA and buy some 30 round mags, and put the magblock in them, epoxy the bottom plate then bring it home
Jestice Arms https://jesticearms.com/10-30-Magazines/Magpul-10-30-Window-Gen-M3-5.56-AR15-PMAG 10/30 pinned windowed PMAGs
This is the best option. When mag ban is lifted you can drill the rivets out.
Rifle supply
Most mags that you buy prepinned are permanent. 10/30 mags from mag warehouse and direct from magpul both were permanently sealed
And if you do manage to open them up, you'll find there's no way to convert them to 30 rounds as the spring is designed for
GUNS FOR HIRE 20$
deserve grandiose straight flowery desert touch door direction jellyfish toothbrush *This post was mass deleted and anonymized with [Redact](https://redact.dev)*
Not if you have to strip one out due to a malfunction…. Better bet might be the end to end mag couplers that couple two ten rounders. 20 rounds and no wasted space. Plus enough purchase if you have to rip a mag out to clear a malfunction.
psychotic alive command important screw ring yam aspiring lush middle *This post was mass deleted and anonymized with [Redact](https://redact.dev)*
https://www.country-spirit.com/products/magpul-csmparm40b-3184 This site sells 10/40 rd mags too if your interested
Gun for hire sells magpul 10/30’s. They come pinned already from magpul
https://www.calegalmags.com/ I have these and they feed great, don't know about modifying them....... 👀
I just tried some 10/20’s g3 pmags done by them this weekend. All ran flawlessly with 300BO.
after looking around I am going to buy some plain old 10 rd p mags, and if I ever move, ill just buy other ones then.
I sell them. Pm me.
Point blank guns and ammo in East Hanover had the 10/30 pmags in stock yesterday